102 lines
3.2 KiB
HTML
102 lines
3.2 KiB
HTML
<div class="hts-doc-text">
|
|
|
|
<h3>The adapters and tuners are listed / edited in a tree</h3>
|
|
|
|
<ul>
|
|
<li>To edit an item, click on it. To commit edited changes back to
|
|
Tvheadend press the 'Save' button. In order to change a Checkbox cell
|
|
you only have to click once in it.
|
|
</ul>
|
|
</p>
|
|
|
|
<h4>The rows have the following functions</h4>
|
|
|
|
<dl>
|
|
<dt>Enabled</dt>
|
|
<dd>If selected, the IPTV service will be enabled an use for channel
|
|
subscriptions.</dd>
|
|
|
|
<dt>Name</dt>
|
|
<dd>The name of this tuner.</dd>
|
|
|
|
<dt>OTA EPG</dt>
|
|
<dd>Allow OTA EPG (epggrab) scan on this input device</dd>
|
|
|
|
<dt>Priority</dt>
|
|
<dd>The tuner priority value (higher value = higher priority to use this
|
|
tuner).</dd>
|
|
|
|
</dl>
|
|
</p>
|
|
|
|
<h4>LinuxDVB specific rows</h4>
|
|
|
|
<dl>
|
|
<dt>Keep FE open</dt>
|
|
<dd>Enable to not close the LinuxDVB frontend device in the idle state.</dd>
|
|
</dl>
|
|
|
|
<h4>SAT>IP specific rows</h4>
|
|
|
|
<dl>
|
|
<dt>Full Mux Rx mode supported</dt>
|
|
<dd>Enable, if the SAT>IP box supports the full mux rx mode (pids=all)
|
|
parameter.</dd>
|
|
|
|
<dt>Signal scale (240 or 100)</dt>
|
|
<dd>Some SAT>IP boxes has only 0-100 scale. If your signal is too low, try
|
|
value 100 here.</dd>
|
|
|
|
<dt>Maximum PIDs<dt>
|
|
<dd>Maximum supported PIDs in the filter of the SAT>IP box.</dd>
|
|
|
|
<dt>Maximum length of PIDs<dt>
|
|
<dd>Maximum length in characters for the command setting PIDs to the
|
|
SAT>IP box.</dd>
|
|
|
|
<dt>addpids/delpids supported</dt>
|
|
<dd>Enable, if the SAT>IP box supports the addpids/delpids command.
|
|
|
|
<dt>PIDs in setup</dt>
|
|
<dd>Enable, if the SAT>IP box requires pids=0 parameter in the SETUP RTSP command.</dd>
|
|
|
|
<dt>Force pilot for DVB-S2</dt>
|
|
<dd>Enable, if the SAT>IP box requiest plts=on parameter in the SETUP RTSP
|
|
command for DVB-S2 muxes.</dd>
|
|
|
|
<dt>UDP RTP Port Number (2 ports)</dt>
|
|
<dd>Force the local UDP Port number here. The number should be even (RTP port).
|
|
The next odd number (+1) will be used as the RTCP port.</dd>
|
|
|
|
<dt>Satellite Positions</dt>
|
|
<dd>Select the number of satellite positions supported by the SAT>IP
|
|
hardware and your coaxial cable wiring.</dd>
|
|
|
|
<dt>Master Tuner</dt>
|
|
<dd>Select the master tuner.
|
|
<p>The signal from the standard universal LNB can be split using
|
|
a simple coaxial splitter (no multiswitch) to several outputs.
|
|
In this case, the position, the polarization and low-high
|
|
band settings must be equal.</p>
|
|
<p>If you set other tuner as master, then this tuner will act like
|
|
a slave one and tvheadend will assure that this tuner will not
|
|
use incompatible parameters (position, polarization, lo-hi).</p>
|
|
</dd>
|
|
|
|
<dt>Next tune delay in ms (0-2000)</dt>
|
|
<dd>The delay before tuning in milliseconds after tuner stop. If the time
|
|
after previous start and next start is greater than this value -
|
|
the delay is not applied.</dt>
|
|
|
|
<dt>Send full PLAY cmd</dt>
|
|
<dd>Send the full RTSP PLAY command after full RTSP SETUP command. Some
|
|
device firmwares requires this to get MPEG-TS stream.</dd>
|
|
|
|
<dt>Force teardown delay<dt>
|
|
<dd>Force the delay between RTSP TEARDOWN and RTSP SETUP command (value
|
|
from 'Next tune delay in ms' is used). Some devices are not able to handle
|
|
quick continuous tuning.</dd>
|
|
|
|
</dl>
|
|
|
|
</div>
|